Measure
Use length × width × thickness, a known paved area plus thickness, or a known volume. Keep each paved section separate when dimensions differ.
CONSTRUCTION CALCULATOR
Estimate how much asphalt you need for a driveway, parking area or paved surface in US tons or metric tonnes. Start with dimensions, a known area or volume, adjust asphalt density, combine multiple paved areas and estimate material cost before you order.
IMPORTED FROM PROJECT BUILDER
Asphalt geometry from Project Builder is ready to calculate.
QUICK PLANNING GUIDE
Use the calculator when you know the paved dimensions, surface area or an existing volume. It converts the project into an order volume and estimated weight so you can plan material before contacting a supplier.
Use length × width × thickness, a known paved area plus thickness, or a known volume. Keep each paved section separate when dimensions differ.
MetricSketch calculates cubic volume, applies your extra-material allowance, converts volume to US tons or metric tonnes and can estimate material-only cost.
Check the specified asphalt mix, compacted density, lift thickness, minimum delivery and supplier pricing. Those project-specific values can change the final order.
ASPHALT PROJECT
MATERIAL ASSUMPTIONS
The default density is a planning value from the calculation engine. Replace it with a project or supplier density when available. Currency switching changes the label only; it does not perform FX conversion.
Use dimensions when you know the length, width and asphalt thickness.
Estimated asphalt weight including the selected extra-material allowance.
Asphalt weight depends on density. Confirm the mix, compacted density, ordering units and supplier requirements before purchasing.
MULTIPLE PAVED AREAS
Add the current calculation to a temporary paving project, then combine driveway sections, parking areas and known asphalt volumes. The selected extra percentage is applied once to the combined base volume.
No paved areas added yet. Calculate a dimensions, known-area or known-volume estimate above, then add it here.
Project areas are temporary for this browser session. The calculator stores each area's base volume and recalculates the combined order using the current extra percentage, density and pricing assumptions.
PROJECT OUTPUT
Turn the current calculation or your combined paving project into a supplier-friendly order summary. Copy it to your notes or print the clean summary to save it as a PDF.
Planning estimate only. Confirm asphalt mix design, compacted density, lift thickness, ordering units, minimum loads, delivery fees and supplier requirements before ordering.
CALCULATION METHOD
MetricSketch first calculates a base asphalt volume from dimensions, known area and thickness, or a volume you already know. It then applies your extra-material allowance and uses asphalt density to convert volume into US tons or metric tonnes. Add supplier pricing when you also want an estimated material cost.
THREE INPUT PATHS
Use length, width and thickness for a rectangular driveway, parking area or paved section.
Start from square feet or square meters when the surface area is already known, then enter the asphalt thickness.
Start from cubic yards or cubic meters when a base asphalt volume has already been calculated elsewhere.
QUICK EXAMPLE
A 20 ft × 10 ft paved area at 3 in thick has a base asphalt volume of about 1.85 yd³. With a 5% extra-material allowance, the order volume is about 1.94 yd³. At the default planning density of 145 lb/ft³, that is approximately 3.81 US tons of asphalt. Add your supplier price per ton to estimate material cost.
Asphalt density, lift design and ordering rules vary by mix and supplier. Confirm the project specification, compacted density, minimum loads and delivery requirements before purchasing.
ASPHALT CALCULATOR FAQ
These answers explain how the tonnage estimate is built and which project assumptions should be confirmed with your supplier.
Calculate the paved volume from length, width and thickness, then convert that volume to weight using asphalt density. MetricSketch performs the unit conversions and can add an extra-material allowance.
Asphalt tonnage is estimated by multiplying the final material volume by asphalt density. Because density varies with the mix and project, use a supplier or project value when one is available.
Yes. Use Known area when you already have the paved surface in square feet or square meters, then enter the planned asphalt thickness to calculate volume and weight.
The calculator includes a default planning density, but it is not a substitute for the mix design or supplier specification. Replace it with the project-specific compacted density whenever possible.
Use the extra-material field when you want an ordering allowance for project variation or handling. Set it to zero when you only want the calculated base quantity.
No. The optional price field estimates material cost from the calculated asphalt weight only. Delivery, minimum-load charges, taxes, labor and equipment are not added unless they are already included in the supplier price you enter.
QUICK PROJECT GUIDE
This asphalt calculator also works as a practical asphalt estimator: enter dimensions, known area or volume, review tonnage, and add supplier price per ton or tonne when you have it.